Key plate made of untreated iron plate of a model that has been common since the 17th century
EUR4.13
Key plate with clapper of ordinary 19th century and early 20th century model. Fits our iron and brass door knobs and our escutcheons, but is also useful for adding to older escutcheons and knobs. With the new dimensions, our lock fittings are also suitable for most modern locks with through-screws.
EUR16.05
Key plate without clapper of ordinary 19th century and early 20th century model. Fits our iron and brass door knobs and our escutcheons, but is also useful for adding to older escutcheons and knobs. With the new dimensions, our lock fittings are also suitable for most modern locks with through-screws.
EUR10.55
Iron key plate of ordinary 19th century and early 20th century model. Fits our iron and brass door knobs and our lever handles, but is also useful when adding to older lever handles and knobs. With the new dimensions, our lock fittings also fit most modern locks with through screws, etc.
EUR10.09
Key ring for large and many keys after old model from Gysinge.
Hand-forged special steel. Diameter approximately 13 cm.
EUR17.88
Hand forged linseed oil fired special steel. Diameter 7 cm
Oval key plate made of untreated iron plate of a model that has been common since the 18th century.
Interior door lock intended for room doors after the middle of the 19th century, when there was a transition from surface-mounted chamber locks to recessed so-called mortise locks. The lock is a 3-keeper lock with 44 different key combinations and can be locked from both the outside and the inside. The lock has recess dimensions according to older standards. Therefore, it is often suitable from the late 1800s onwards. This lock is suitable for our prints and knobs, as well as accessories in the form of key plates, rosettes, long plates, etc.
Lock body and lock plate in galvanized steel. Supplied with two keys and strike plate. The latch bolt is reversible when dismantled, i.e. a right-hand lock can be turned into a left-hand lock and vice versa. Counter plate included. Equal locking with the same key for several locks can be specially ordered. Thorn depth 4.5cm.
Please note that the dimensional sketch is mirrored in relation to the product image.
EUR171.94
Interior door lock intended for room doors after the middle of the 19th century, when there was a transition from surface-mounted chamber locks to recessed so-called mortise locks. The lock is a 3-keeper lock with 44 different key combinations and can be locked from both the outside and inside.
The lock has recess dimensions according to older standards. Therefore, it is often suitable from the late 1800s onwards. For this lock, our prints and knobs fit, as well as accessories in the form of key plates, rosettes, long plates, etc.
Lock body and lock plate in galvanized steel. Supplied with two keys and strike plate. The latch bolt is reversible when dismantled, i.e. a right-hand lock can be turned into a left-hand lock and vice versa. Counter plate included. Equal locking with the same key for several locks can be specially ordered. Pin depth 4.5 cm
The locks are relatively similar throughout the ages. Most commonly, they were used in combination with a deadbolt or padlock on outbuilding and shed doors.
EUR29.80
Strong, wide, hand-forged lock spring for chamber locks and other locks from before the middle of the 19th century.
EUR23.84
Lock spring for chamber lock of turn of the century type 1900. Fits normal lock chests. Depending on the lock model, the spring may need to be bent or cut. Length 4.5 cm, width 6 mm
EUR9.17
Wooden lock plug, 2-pack. Many modern doors have large milled holes for standard modern handles and through-screw locks. Customers who want traditional fittings can therefore not choose them. But here is the solution. The wooden plug is used to plug oversized holes so that you can switch to traditional prints and key plates. The plug is fixed with glue in the empty holes.
EUR5.04
Hand-forged marlin. Linseed oil fired iron. 45 mm.
Hand-forged marlin.
Linseed oil fired iron. Length 60mm.
EUR4.59
Posthorn iron in brass
The posthorn iron is delivered including thrust washers, 8 mm square pin, wood screw and bushing to fit both older and modern locks.
For dimensions see picture
EUR201.28
Nickel-plated thrust washer/rosette sold per pair
Suitable screw number 19.
EUR21.55
Rosette in brass of ordinary 1800 and early 1900s model. Fits our brass door knobs and lever handles, but is also useful when adding to older lever handles and knobs. With the new dimensions, our lock fittings also fit most modern locks.
Rosette in iron of ordinary 1800 and early 1900s model. Fits our door knobs but is also useful when supplementing older prints and knobs. With the new dimensions, our lock fittings also fit most modern locks with through screws, etc.
Hand-forged bolt, short model for external doors. Used for double doors where one door leaf is intended to be fixed and the other openable. Common model from the end of the 18th century to the middle of the 19th century. Long sliding bolt is mounted at the top of the door and short at the bottom. Can be used both as surface-mounted or recessed fittings. Supplied together with a closing plate for the door frame.
EUR91.24
Iron sliding bolt for doors. Traditional model 1800 – 1900s.
EUR12.75
EUR11.83
Hand forged bolt, long model for external doors. Used for double doors where one door leaf is intended to be fixed and the other openable. Common model from the end of the 18th century to the middle of the 19th century. Long sliding bolt is mounted at the top of the door and short at the bottom. Can be used both as surface-mounted or recessed fittings. Supplied together with a closing plate for the door frame.
EUR100.41
Sleeve to equalize the difference between an 8 mm rod and a 9 mm hole.
EUR1.65
